Same issue here......
Sure would be nice to be able to scroll.
Ken
| 14Point7.com |
|
September 09, 2010, 03:47:07 AM
|
|||
|
|||
| 14Point7.com |
|
|
September 09, 2010, 03:47:07 AM
|
|||
|
|||
| Home | Help | Search | Login | Register |
|
1
JAW: Just Another Wideband (Wideband Reader) / JAW Edit Software Issues / Re: Changes to JAW EDIT to allow scrollable windows for letterbox netbook displays
on: September 08, 2010, 06:41:39 PM
|
||
| Started by Dr John C Bullas a.k.a. Dr B - Last post by kjones6039 | ||
|
Same issue here......
Sure would be nice to be able to scroll. Ken |
||
|
2
JAW: Just Another Wideband (Wideband Reader) / JAW Edit Software Issues / Changes to JAW EDIT to allow scrollable windows for letterbox netbook displays
on: September 08, 2010, 03:03:33 PM
|
||
| Started by Dr John C Bullas a.k.a. Dr B - Last post by Dr John C Bullas a.k.a. Dr B | ||
|
Hi!
I want to use an MSI Wind netbook for the real-time operation of my JAW 1.03 in the car I just saw the latest download for EDIT still did not have any scrollbars my 1200 x 600 display cannot show all the info but could if there was a vertical scrollbar  any way for me to tweak the source code if ADMIN is too busy now?DR B |
||
|
3
JAW: Just Another Wideband (Wideband Reader) / JAW Edit Software Issues / Re: COM Port settings for USB-Serial adapter?
on: September 08, 2010, 03:01:21 PM
|
||
| Started by eclipsh - Last post by Dr John C Bullas a.k.a. Dr B | ||
|
the art to finding the com port the usb to serial setup creates is to see it appear in control panel > system > hardware > universal serial bus controllers OR just see the extra port appear in EDIT (run it before and after the dongle is connected)
hope this helps DR B |
||
|
4
on: September 08, 2010, 02:20:13 PM
|
||
| Started by ek4swe - Last post by prj | ||
|
TP_REF to GND is 2.50V
TP_12V to TP_GND is 12.05V 5V to GND is 5.03V Resistance between 5V and Ground is 679 ohms. The moment I power the unit from a 12V power supply, Pin 6 goes to 0.9V and stays there. |
||
|
5
SLC (Sigma Lambda Controller) / SLC DIY / Re: Bug in Firmware 1.03, will show 62.24 when richer than 10.26 AFR
on: September 08, 2010, 07:07:49 AM
|
||
| Started by admin - Last post by motorica | ||
|
Just to clarify, according to slc edit the firmware version is 3
Does it means it is 1.03 ? If so is there away to replace the firmware not by sending the unit to you ? This bug is an issue to me too David |
||
|
6
on: September 08, 2010, 02:11:17 AM
|
||
| Started by ek4swe - Last post by prj | ||
|
Switching crossover point works now, but regardless of value, pin 6 output is still 0.9V at all times.
|
||
|
7
on: September 08, 2010, 12:53:32 AM
|
||
| Started by prj - Last post by prj | ||
|
Works now.
|
||
|
8
on: September 07, 2010, 06:47:38 PM
|
||
| Started by prj - Last post by admin | ||
|
try again now, i reuploaded the software to my ftp site.
|
||
|
9
on: September 07, 2010, 12:46:46 PM
|
||
| Started by ek4swe - Last post by prj | ||
|
Here are my calibration values:
 Is it normal to measure a voltage of 1.08V between Pin 11 and Pin 6 with only USB connected? |
||
|
10
on: September 07, 2010, 05:30:07 AM
|
||
| Started by ek4swe - Last post by prj | ||
|
My narrowband output is stuck at 0.9 volts regardless of AFR.
The AFR display seems to work fine. I have tried: 1. Hardware calibration, multiple times 2. Resetting memory, multiple times 3. Changing the crossover point, but SLC Edit always just says "Error 0", and I am unable to change it. What could be wrong? |
||
